Rim cleaning and tire care set

Product information
Rim cleaning and tire care set
SCHOLL Concepts GmbH Logo
Rim cleaner
RIM-7 is an intelligent and acid-free cleaner with colour change for effortless cleaning of heavily soiled rims of almost any kind. The high viscosity ensures that the cleaner works where you spray it on and does not run off. An intelligent dirt-dissolving indicator turns the cleaning gel purple after the optimum exposure time (2-3 minutes) and shows the user that the rim can be sprayed off with water.

Shake RIM-7 vigorously before application. Now spray the entire surface of the rims from a distance of approx. 40 cm. Allow to act for approx. 2 to 3 minutes and then rinse thoroughly with a strong jet of water. In the case of stubborn dirt, clean with the purple SCHOLL Spider application puck before rinsing. In contrast to conventional, often highly acidic rim cleaners, RIM-7 cleans extremely gently thanks to its pH-neutral formulation. For very high-quality or exotic rims, we recommend testing the material compatibility in an invisible place to be on the safe side. Never use RIM-7 on hot rims.

Tyre care 
SLIME Tyre Dressing Gel. Viscose premium shine care for tyre and rubber surfaces. SLIME is characterised by its intensive shine that lasts for weeks. The product is free of hydrocarbons. SLIME - Tyre Dressing Gel dries within minutes and leaves no greasy film. 

Apply SLIME only to the cleaned vehicle. Apply the gel to the black application puck and then spread SLIME evenly over the tyre. Done! Tyre Dressing Gel can also be easily applied to all unpainted hard plastic and rubber surfaces. Benefit from over 60 years of experience in the field of car care products.

Included in the bundle:


·       1 x RIM 7 Wheel Cleaner Gel 500 ml (11022)

·       1 x SLIME Tyre Dressing Gel 500 ml (12020)

·       1 x Spider Cleaning Puck 100/50 mm purple (22687)

·       1 x Hand Puck 100/50 mm black (22688)

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Polishing pads are made up of different materials and come in different shapes and sizes. The choice of the right kind of pad, however, depends mainly on the application and required cut. Lambskin polishing pads have given rise to one of the most common misconceptions we have about polishing pads. The lambskin pad is the most abrasive polishing pad with the highest cut that we know of. The differences between the various polishing pads are as follows:


Premium SOFTouch Topwool
Premium polishing pad made from 100% natural wool and integrated orange foam interface layer, for maximum cutting performance on fresh and worn paint surfaces.

Sandwich SpiderPad (black/white)
Innovative foam pad with calibrated surface and double-layer structure for maximum cutting performance and low heat build-up on fresh paint surfaces.

SpiderPad (navy-blue)
Firm, reticulated premium polishing pad. A brand new, unique heat-resistant foam composition provides a steady and consistent cutting performance.

Polishing pad (purple)
Superior, firm foam pad with a coarse porous structure, ideal for paint detailing applications. The tear-resistant, reticulated foam composition provides maximum durability.

FINE (5)
All-purpose sponge (orange)
This all-purpose, semi-firm pad with a fine, closed-cell foam structure is ideal for final finish and sealing applications.

FINE (6)
SpiderPad Neo (yellow)
This fine porous, reticulated hybrid pad with a calibrated surface was designed for the efficient application of the NEO Polymer Protection. Ideal for removing holograms.

SOFTouch-Waffle Pad (black)
Extremely fine and soft foam pad with an extra orange interface layer for controlling contact pressure on the surface to be polished.

If the pad begins to dust or stick during polishing, it is time to clean and remove the accumulated dirt and used polish from it. The easiest way to do this is by using the cleaning brush. Simply press the brush against the rotating pad at low speed and allow the bristles to brush the dirt out. After polishing, all pads can be washed out with water and a little cleaning agent. Note that lambskin pads should be left wet and re-attached with the Velcro face onto the polishing plate in order to prevent them from shrinking and losing their shape.

This can be caused by various reasons:

a) The polisher is turned on before bringing the pad into contact with the paint (frequent beginner’s error)
b) Polisher speed too high
c) Too much polish
d) Tilting of polisher / formation of dust when polishing edges
e) Use of new pad that has not yet been worn in
f) Fresh pad, into which the polishing compound has not been distributed evenly prior to polishing

1. Make sure that the entire surface of each new pad is coated sparingly and evenly with the required polish. (Note: Any part of the pad that is not coated with polish may cause micro-scratches.)
2. The rubbing compound should be spread across several points onto the paint surface with the pad and then distributed evenly and rubbed in (BEFORE TURNING ON THE POLISHER). The aim is to have sufficient unused rubbing compound over the entire surface in order to ensure a uniform cut.
3. Now set the polisher/pad onto the paint surface and check whether you have set the polisher to the right speed.
4. The actual polishing process can now begin. Switch on the polisher.
5. Proceed by applying the compound in a criss-cross movement. Make sure that the area of the surface you wish to work on is not too large. Always remember: you should be able to cover the selected surface from one comfortable position.

Product videos


60 years of experience in paint finishing solutions

Headquartered in Remseck, Germany, SCHOLL Concepts GmbH has been catering to the requirements of the car care industry for 60 years by providing premium, innovative car care and maintenance systems for the automotive repair and paint industry. Our commitment and passion to create the perfect paint finish has made us one of the global leaders in innovative and customised solutions and the leading experts for comprehensive paint finish solutions.

Our corporate culture focuses on providing premium products and services. To implement this strategy, we pursue an integrated approach. High-grade, innovative and unique products and ideas can only develop when this philosophy is an integral part of our corporate culture and all processes, facilities and equipment are geared to meet the highest quality demands. Thanks to their distinctive brand names, among other features, our pre- mium products are easily identifiable and enjoy a high level of awareness.



Our life is defined by 3 spatial dimensions and as biological beings we developed in 3 dimensions. So what could be more natural than viewing our business in 3 dimensions? Get to know our unique B2B concept: SCHOLL Concepts does not just develop high quality and individual premium products but also an intelligent overall concept for their effective commercialization.